<%NUMBERING1%>.<%NUMBERING2%>.<%NUMBERING3%> PRTG Manual: Detailed System Requirements

This section shows different aspects of system requirements for PRTG. Please consider these requirements to avoid issues while monitoring your network.

icon-prtg-on-demandPRTG hosted by Paessler does not require any hardware for the PRTG server, but at least one remote probe installation is necessary to monitor your local network when using PRTG hosted by Paessler.

Supported Operating Systems for PRTG Server and Remote Probes

The 32-bit and 64-bit versions of the following operating systems are officially supported for PRTG Core Service and Probe Service:

  • Microsoft Windows Server 2012 R2* (recommended)
  • Microsoft Windows Server 2016*
  • Microsoft Windows Server 2012*
  • Microsoft Windows 10**
  • Microsoft Windows 8.1
  • Microsoft Windows 8
  • Microsoft Windows 7
  • Microsoft Windows Server 2008 R2*

* Windows servers in Core mode or Minimal Server Interface are not officially supported.

** The PRTG Enterprise Console is not fully compatible with Windows 10.

The version (32-bit or 64-bit) of the PRTG Core Server depends on the version of your operating system. The 64-bit version of the PRTG Core Server will be installed if

  • the operating system is a 64-bit Windows system, and
  • the system provides 6 GB RAM or more.

Otherwise the 32-bit version of the PRTG Core Server will be installed.

  • For best performance of VMware sensors, EXE/Script sensors, and some other sensor types, we recommend Windows Server 2012 R2 on the computer running the PRTG probe: This is either on the local system (on every node, if on a cluster probe), or on the system running a remote probe.
  • For best performance of hybrid sensors using Windows Performance Counters and Windows Management Instrumentation (WMI), we recommend Windows 2008 R2 or higher on the computer running the PRTG probe: This is either on the local system (on every node, if on a cluster probe), or on the system running a remote probe.
  • Microsoft .NET Framework: We recommend that you provide Microsoft .NET Framework versions 4.5 or later (with latest updates) on all systems running a PRTG probe.
    The .NET framework is imperatively needed for monitoring VMware and XenServer virtual environments. Also some other sensor types need the Microsoft .NET Framework to be installed on the computer running the PRTG probe. This is either on the local system (on every node, if on a cluster probe), or on the system running a remote probe. Required versions are 4.5, 4.6, or 4.7. For details, see the Knowledge Base: Which .NET version does PRTG require?
  • Disabled FIPS Mode: Ensure the FIPS (Federal Information Processing Standards) mode (Windows security option "System Cryptography: Use FIPS compliant algorithms for encryption, hashing, and signing.") is disabled on Windows systems running the PRTG core or probe service. FIPS-compliant encryption may cause errors of sensors which use the .NET framework. For details, see the Knowledge Base: Why should I disable the FIPS mode under Windows?  

Hardware Requirements for PRTG Server and Remote Probes

Hardware requirements for PRTG Core Service and Probe Service mainly depend on the sensor types and intervals used. The following values are provided as reference for common usage scenarios of PRTG (based on a default sensor interval of 60 seconds).

  • CPU
    A current PC or server with at least a dual core CPU can easily monitor up to 2,000 sensors (see sensor type specific notes below). PRTG supports native x86/x64 architectures.
  • RAM
    Minimum requirement: 2048 MB RAM. You need about 150 KB of RAM per sensor.
  • In general, we recommend at least 1 additional CPU core and 1 GB RAM per additional 1,000 sensors.
  • Hard Disk Drive
    You need about 200 KB of disk space per sensor per day (for sensors with 60 second interval).
  • Internet connection
    An internet connection is required for license activation (via HTTP or email).
  • Stable network connection for remote probes
    Remote probes require a stable network connection between the PRTG core server and the remote probe. Unstable connections, for example via 3G, might work but it could be possible that you lose monitoring data if the connection is non-reliable.

There are also non-hardware dependent limitations for some sensor types, for example, WMI and SNMP V3 sensors. These limitations can be overcome by distributing the sensors across multiple remote probes. For clusters we recommend that you stay below 2,500 sensors per cluster.

icon-i-redIt is crucial for a properly working PRTG server to have a certain amount of hardware resources available. If the server runs out of resources, PRTG will send warning and emergency messages to the primary email address of the PRTG System Administrator user. You will receive warning messages if available disk space falls below 1 GB or memory below 500 MB, and emergency messages if available disk space or memory falls below 50 MB. Please react immediately and free up system resources!

Network Size: Recommendations

  • Rule of thumb: Typical PRTG installations almost never run into performance issues when they stay under 5,000 sensors, under 30 remote probes, and under 30 user accounts.
  • PRTG can scale much higher if the installation is well planned. Please read on if you plan to go beyond these numbers and/or if you plan elevated use of resource intensive features like reporting, xFlow sensors, or clustering.
  • If you plan an installation that monitors more than 10,000 sensors from one instance of PRTG on a physical device or more than 5,000 sensors with PRTG running on a virtual machine, we ask you to contact your presales team for consultation.
  • To give you an impression: To monitor 5,000 sensors in a 1-minute interval, PRTG takes 7.2 million measurements and evaluates, notifies, and stores them—this adds 700 MB of additional data to the database every single day.

icon-prtg-on-demandPRTG hosted by Paessler is restricted to max. 5,000 sensors, more sensors are not possible. This number of sensors is available in the PRTG-5000 subscription.

Apart from the processing power required for the monitoring itself, several aspects can affect the number of sensors that you can use with PRTG. The following recommendations are for a PRTG single core setup (without clustering) on a physical machine. You can overcome some of these limitations if you distribute the sensors across multiple remote probes.

Size Recommendations

Operating System

We recommend that you use Windows Server 2012 R2 to run the PRTG core server and probes. This offers superior performance for monitoring, especially if you have more than 2,000 sensors.

Sensor Types

Ping and SNMP sensors create much less load than complex sensors like xFlow sensors, VMware sensors, Sensor Factory sensors, WMI sensors, or Syslog/Trap receiver sensors, for example.

Scanning Interval

We recommend that you mainly use 1-minute scanning intervals for up to 2,000 sensors and 5-minute intervals if you have more sensors.

Number of Users

We recommend that you stay below 30 active user accounts for each PRTG core server. You can work well with more users if these do not all use the user interfaces at the same time (including public dashboards).

Number of Remote Probes

Our general recommendation is to stay below 30 remote probes on one PRTG core server. PRTG still scales well up to 60 probes as long as you have less than 100 sensors per probe.

CPU Intensive Features

Try keeping the usage of the following features down: Many quickly refreshed dashboards, frequent generation of huge sensor reports, heavy usage of packet sniffing, factory sensors, and Toplists, frequent automatically scheduled auto-discoveries for large network segments, constant queries of monitoring data via the API, among others.

Network Connection Quality

The quality of your network also plays an important role. When monitoring via UDP, for example, a high packet loss rate can lead to frequent timeouts. Remote probes that connect via unstable (WAN) connections can lead to delays as well.

In general, consider the following rules for the performance impact of different sensor types:

  • SNMP V1 and V2, Ping, Port, and HTTP
    We recommend that you use these sensor types for scenarios with thousands of sensors.
  • SNMP V3
    You can monitor about 5,000 SNMP V3 sensors with an interval of 60 seconds on a common two core computer, and about 10,000 sensors on a four core system (the main limiting factor is your CPU power).
  • WMI
    Try to keep the number of WMI sensors per probe below 120 sensors (with 60s interval), or 600 sensors (with 300s interval).
  • xFlow (IPFIX, NetFlow, sFlow, jFlow)
    Monitoring the maximum number of sensors depends on the traffic pattern, the number of xFlow packets per second received by the PRTG probe, as well as the performance of the probe system.
  • Packet Sniffer
    These sensors create the highest CPU load on the probe system. This technology is only recommended for monitoring of low traffic connections (<50 Mbit/s steady stream). When traffic is often over 10 Mbit/s a dedicated remote probe should be used.
  • VMware Monitoring
    Monitoring of VMware is limited to about 20 sensors at a 60 seconds monitoring interval, or 100 sensors at a 5 minutes interval. On probes running on Windows Server 2012 R2, you can use more VMware sensors. These limitations issue from the VMware platform. For details, see this Knowledge Base article: Increasing Maximum Connections for VMware sensors
  • Other sensor types
    The impact of a specific sensor type on performance is indicated by a color range when adding a sensor to a device. It ranges from dark green (very low impact) to bold red (very high impact).

To overcome any limitations mentioned above you should distribute the sensors over two remote probes or more.

Running PRTG on Virtual Machines

You can run the PRTG core server as well as PRTG remote probes on virtualized platforms. However, we strongly recommend that you use a dedicated physical machine to run the PRTG core server or the PRTG remote probes.

There are several reasons why we recommend that you run PRTG (core server and remote probes) on real hardware, especially for thousands of sensors. Each sensor request will have to go through many virtualization layers, which costs performance and makes measurements less exact. In our experience, a physical machine simply works best for a thousand sensors and more.

Our recommendation to use real hardware is valid for the PRTG core server and for remote probes. If you must run PRTG on a virtual machine, please stay below 5,000 sensors per virtual machine and consider running several PRTG core server instances instead.

icon-i-round-redWe cannot offer technical support regarding performance and stability problems for PRTG installations on virtual machines that run with more than 5,000 sensors. In this case, please migrate PRTG to one or more, preferably physical, machines.

icon-i-roundWhen running PRTG on a virtual machine, do not use dynamic resource allocation, but please make sure that full resources are available to the virtual machine at any time. In our experience, dynamic resource allocation is not working efficiently for a monitoring software and can lead to massive performance issues. Do not distribute CPU cores over different CPU sockets in your VM configuration. Scheduling threads does not work properly in this case, which results in performance issues.

icon-book-bulbFor more details, see this Knowledge Base article: Checklist for Running PRTG on VMware

Running PRTG in a Failover Cluster

We recommend a single failover setup if you need fail-safe monitoring. This consists of two PRTG core servers, each working as a cluster node.

In a PRTG failover cluster, the monitoring load doubles with each cluster node, so you will encounter half performance for each additional cluster node. In a single failover cluster, please divide our recommended numbers from above in half.

icon-prtg-on-demandThis feature is not available in PRTG hosted by Paessler.

Web Browser Requirements

The following browsers are officially supported by the PRTG web interface (in order of performance and reliability):

  • Google Chrome 61 or later (recommended)
  • Mozilla Firefox 56 or later
  • Microsoft Internet Explorer 11

For security and performance reasons, we strongly recommend that you always use the latest version of Google Chrome to access the PRTG web interface.

icon-i-round-redFirefox is potentially vulnerable for cross-site scripting (XSS) attacks. These XSS exploits are possible if you click phishing links that contain malicious code, for example, in emails, and you are currently logged in to PRTG with Firefox. For more information, see this Knowledge Base article: How secure is it to access the PRTG web interface with Firefox?

icon-i-roundMicrosoft Internet Explorer 11 and Microsoft Edge, as well as other current browsers that are not officially supported have issues with some functionalities of the PRTG web interface. However, you can access the web interface with any browser.

icon-i-roundDeprecated Internet Explorer versions as well as some mobile browsers might not be able to display the fully featured Ajax web interface.

icon-i-roundPlugins may have an effect when viewing the PRTG web interface. Please make sure to add exceptions for PRTG in the plugins' settings, especially when using ad blockers. See also this Knowledge Base article: The logs page in the PRTG web interface does not load. What can I do?

Screen Resolution

A screen resolution of at least 1024x768 pixels is sufficient for most functions of PRTG. However, we recommend a screen resolution of 1200x800 or higher.

Requirements for Monitored Devices

  • SNMP monitoring
    The monitored device(s) must be equipped with SNMP Version 1, 2c, or 3 (an SNMP-compatible software must be installed on the device). SNMP must be enabled on the device and the machine running PRTG must be granted access to the SNMP interface. For details, see section Monitoring via SNMP.
  • Windows/WMI monitoring
    To use Windows Management Instrumentation (WMI) monitoring, you need a Windows network. For client PCs monitored with WMI, only the operating systems as given above are officially supported, but do not use Windows 2008 for WMI monitoring (strong performance issues). For details, see section Monitoring via WMI.
  • xFlow (IPFIX, NetFlow, sFlow) monitoring
    The device must be configured to send NetFlow data packets (NetFlow version 5, 9, or IPFIX) or sFlow packets (version 5) to the machine running the PRTG probe. For details, see section Monitoring Bandwidth via Flows.
  • Packet Sniffer monitoring
    Only data packets passing the local machine's network card can be analyzed. Switches with so-called 'monitoring ports' are necessary for network-wide monitoring in switched networks. For details, see section Monitoring Bandwidth via Packet Sniffing.
  • Other sensor types
    Depending on the specific sensor type, you can find requirements (for example, modules, components, device configurations) that may have to be fulfilled in the corresponding manual section, as well as when adding the sensor to a device.

Requirements for the Enterprise Console

The optional PRTG Enterprise Console (EC) runs under all supported Windows versions, but it is not fully compatible with Windows 10. Running the EC on Windows 10 results in several issues so please use another operating system. We will consider full Windows 10 support for future PRTG desktop clients.

icon-prtg-on-demandPRTG hosted by Paessler does not support connections from the Enterprise Console. If you want to use it, please connect the Enterprise Console to a PRTG on premises instance.

The EC has a built-in webkit browser engine and requires no specific browser installed on the system. See also Enterprise Console—Requirements for Connections to PRTG Web Server(s).

Requirements for Smartphones and Tablets

PRTG supports optional mobile apps for iOS and Android devices.

icon-book-arrowsFor more information and system requirements, see section PRTG Apps for Mobile Network Monitoring.

More

Paessler Website: System Requirements for PRTG Network Monitor—Recommended Setup for Most PRTG Users

Knowledge Base: How can I speed up PRTG—especially for large installations?

Knowledge Base: My WMI sensors don't work. What can I do?

Knowledge Base: Frequent Questions about xFlow, Packet Sniffing, Traffic Monitoring and Cisco

Knowledge Base: Increasing Maximum Connections for VMware Sensors

Knowledge Base: My SNMP sensors don't work. What can I do?

Knowledge Base: Checklist for Running PRTG on VMware

Knowledge Base: Which ports does PRTG use on my system?

Knowledge Base: Which .NET version does PRTG require?

Knowledge Base: How secure is it to access the PRTG web interface with Firefox?

Knowledge Base: Why should I disable the FIPS mode under Windows?

 

Introduction Topics

 

Keywords: